Skip to main content

Mold (Mould) Air Sampling Equipment – Certified Testing

The Mycometer mold (mould) sampling equipment start package includes everything you need to collect reliable air samples following the Mycometer Air Sampling Protocol. Each component is designed for accuracy, consistency, and ease of use in the field.

The air sampling start package includes:

  • Trolley – a sturdy base for transporting and positioning your sampling equipment.
  • DVP Pump – ensures precise airflow during mold (mould) air sampling.
  • Tripod Stand – keeps equipment stable for accurate, repeatable measurements.
  • Manifold with Rotameters – available with one or two rotameters to control air distribution.
  • Handheld Makita Leaf Blower – simulates air disturbance for representative mold (mould) sampling conditions.
  • Battery Charger – powers your portable sampling equipment for extended use.
  • Timers (x2) – allow for controlled, consistent sample collection.

Mycometer mold (mould) sampling equipment start package with pump, tripod, manifold, blower, timers, and accessories for certified air testing.

Certification & Training

A 4–5 hour proficiency course is included with the Mycometer mold (mould) sampling equipment start package. This course is mandatory and provides the certification number required to perform professional air sampling with confidence.

⚠️ Note: Lithium batteries cannot be shipped outside Denmark and are not included in the start package.

The Pump

Sampling is conducted using one or two membrane filters, which can cause significant back-pressure, necessitating a strong pump. We recommend and sell the DVP pump, a powerful rotary vane pump capable of providing optimal flow rates required for sufficient sampling volumes.

If you already have a pump, ensure they offer a minimum flow rate of 10 liters per minute (LPM). However, higher flow rates are generally preferable. The DVP pump can easily achieve 25 LPM with a single filter and 17-18 LPM with two filters simultaneously (necessary for running FAI samples).

DVP pump used in Mycometer mold (mould) sampling equipment, providing strong airflow for accurate certified air testing.

Note! pump flow rates given by manufacturers are measured without filters, so a pump rated at 15 LPM may deliver substantially less when filters are attached due to back-pressure.

If you have doubts as to whether the pump you have will be sufficient, write to us on in**@*******er.com and we will try to help you.

The Tripod Stand & Manifold

A stable tripod stand ensures accurate sampling. The manifold with rotameters comes in three variations, depending on the type of mold (mould) sampling required:

  1. The manifold (1:1) for only one filter contains 1 rotameter, 1 filter holder, 1 pump inlet. To be used if only using Mycometer air Fungi or Mycometer air Allergen.
  2. The manifold (2:1) for two filters contains: 2 rotameters, 2 filter holders and 1 pump inlet. To be used for Mycometer air FAI tests.
  3. The manifold (2:2) for two filters contains: 2 rotameters, 2 filter holders and 2 pump inlets. To be used for Mycometer air FAI tests, if you instead of one strong pump have two weaker pumps (one for each filter).

The Rotameters

Accurate calibration is critical when using mold sampling equipment.

As a rule, rotameters cannot be used without Mycometer calibration. Factory-set rotameters are typically calibrated for operation without the flow resistance of a filter, leading to inaccurate readings when a filter is used. This principle applies in both directions: a Mycometer-calibrated rotameter is also unsuitable for sampling without a Mycometer MCE filter.

Mycometer-calibrated rotameters for mold (mould) sampling equipment, ensuring accurate airflow measurement during certified air testing.

A Mycometer calibrated rotameter should have a label on the side of the rotameter. Don’t use rotameters without this label unless you are using a primary calibration unit.

Close-up of Mycometer flowmeter in mold (mould) sampling equipment, calibrated for precise airflow control in certified air testing.

The Blower

Standardizing airflow is essential in air sampling. Mycometer recommends the Makita handheld blower (LXT models DUB 182, 183, 185z, 186z) as part of the mold sampling equipment package.

If another type is used it should be tested that it can give a wind speed between 3,2-3.8 meter per second at two meters.

Makita handheld blower used in Mycometer mold (mould) sampling equipment for standardized air disturbance during testing.

Use the Makita LXT models DUB 182, 183, 185z, and 186z and use without the rubber nozzle.
For speed settings:
Models DUB 182 and 183: Use speed setting 3.
Models DUB 185z and 186z: These are more powerful models; use speed setting 2.

Please note that batteries cannot be shipped internationally from Denmark, so you will need to
obtain them locally. Tip: Choose batteries with a higher Ah rating (from 3 to 9 Ah) for longer use
between charges.